06 noviembre 2010

CODIGOS DE FALLA Di 2510

• The Transport Motor Lock signal remains set to H
for a set period of time while the Transport Motor is
turning.

C0010 Imaging Unit Motor Failure
• The Imaging Unit Motor Lock signal remains set to
H for a set period of time while the Imaging Unit
Motor is turning.
• The Imaging Unit Motor Lock signal remains set to
L for a set period of time while the Imaging Unit
Motor remains stopped.

C0044 EDH Fan Motor Failure
• Refer to the Service Manual for the relevant
option.

C0045 Cooling Fan Failure
• The Cooling Fan Motor Lock signal remains set to
H for a set period of time while the Cooling Fan
Motor is turning.
• The Cooling Fan Motor Lock signal remains set to
L for a set period of time while the Cooling Fan
Motor remains stopped.

C004E Power Unit Cooling Fan Failure
• The Power Unit Cooling Fan Motor Lock signal
remains set to H for a set period of time while the
Power Unit Cooling Fan Motor is turning.
• The Power Unit Cooling Fan Motor Lock signal
remains set to L for a set period of time while the
Power Unit Cooling Fan Motor remains stopped.

C004F IU Cooling Fan Failure
• The I/U Cooling Fan Motor Lock signal remains set
to H for a set period of time while the I/U Cooling
Fan Motor is turning.
• The I/U Cooling Fan Motor Lock signal remains set
to L for a set period of time while the I/U Cooling
Fan Motor remains stopped.

C0214 Abnormal Image Transfer Voltage
• The image transfer voltage exceeds 100 V for the
set period of time while the Imaging Unit Motor
remains stopped.

C0500 Fusing Warm-Up Failure (Main)
El código C0500 se puede restablecer con los siguientes pasos:
 1. Pulse el soft de inicialización en la parte derecha del panel de control. {ES UN AGUJERO PEQUEÑO puede utilizar CLIP)
2. Cuando el punto aparece en la pantalla al iniciar el sistema, pulse la tecla  número 3.
3. El modo cambiará a la pantalla de inicialización.
4. Seleccione la opción para restablecer problemas.
5. Después de reiniciar el código será borrado.

C0501 Fusing Warm-Up Failure (Sub)
• The Fusing Roller Sub Thermistor does not detect
the required temperature within 30 sec. after a
warm-up cycle has begun; therefore, the copier
does not complete the warm-up cycle.
• The temperature of the Fusing Rollers does not
reach the required level even after the set period of
time has elapsed during a warm-up cycle. 

C0510 Low Fuser Temperature Failure (Main)
• The Fusing Roller Thermistor and Fusing Roller
Sub Thermistor are detected to be at a temperature
below 105 °C during standby.
• The Fusing Roller Thermistor and Fusing Roller
Sub Thermistor are detected to be at a temperature
below 105 °C during printing.

C0511 Low Fuser Temperature Failure (Sub)

C0520 High Fuser Temperature Failure (Main)
• The Fusing Roller Thermistor and Fusing Roller
Sub Thermistor are detected to be at a temperature
above 240 °C when the Power Switch is set to
ON.
• The Fusing Roller Thermistor and Fusing Roller
Sub Thermistor are detected to be at a temperature
above 240 °C when the Power Switch is set to
ON.

C0521High Fuser Temperature Failure (Sub)

C0650 Faulty Scanner Home Position Sensor
• The Scanner Home Position Sensor is not blocked
even after the lapse of a given period of time after
it has been unblocked when the Start key is
pressed.

C0900 3rd Drawer Lift-Up
Motor Failure
• The Lift-Up Sensor is not unblocked even after the
set period of time has elapsed after the paper liftup
operation for the drawer has begun.

C0910 2nd Drawer Lift-Up
Motor Failure

C0920 1st Drawer Lift-Up
Motor Failure

C0950 4th Drawer Lift-Up
Motor Failure

C0960 Manual Bypass Paper-Lifting Failure
• The Manual Feed Tray Lift-Up Sensor (PC29) is
not blocked or unblocked even after the set period
of time has elapsed after the Manual Paper Feed
Pick-Up Solenoid (SL3) is energized after the manual
feed paper take-up operation has begun.

C0990 LCC Elevator Motor
Failure